uVSR Normal Trigger@Repair parts & How to build inv
|
|
VSR Normal Trigger Repair parts and How to build in
The Repair parts for Normal Trigger isn't same as for PDI New Trigger.
They have different Trigger system.Please read this page about it.
If you haven't open or build in any parts in VSR Trigger BOX, please read this page.
|
< Let's opem the Trigger BOX >
Trigger BOX is fixed by screws.
When open the BOX, be carefull because the springs(Karu-Bane) may be pop out.
Please Note ;
When close the BOX, please don't fix the hex wrench too tight.
Don't open the BOX on the mussy desk not to miss screws or other small parts. |
|
|
|
< Cross-section view >
If you want to see the details ,please click the name of article.
|
|
< Difference between Normal and PDI's Trigger >
EShape of End and Sear
EMotion of Piston in the Cylinder (by Shape of End and Sear)
EMaterials
The normal piston end gets stuck on the sear sideling.
The PDI New Trigger's sear stands straight and gets stuck on piston tightly.
Please note ;
*The normal piston and end cannot be seperated , they are as a unit. So you cannot use with piston end for PDI New Trigger. If you use PDI New Trigger, you need PDI piston.
*You cannot attach the normal piston and PDI New Trigger because of their end and sear. (Please see below picture. )
*Please select PDI repair parts for PDI New Trigger.
The detail of "Trigger Problems" is HERE. |
PDI Λ(New) Trigger's End and Sear... |
|
|
|
This End is for Λ(New) Trigger.
Made of SUS.
It is included trigger set. |
PDI Λ(New) Trigger's Sear.
Made of S45C. |
The Sear gets stuck on piston tightly. |
The Normal Piston End and Sear ... |
|
|
|
This is normal Piston and End.
Made of Resin.
*The normal piston and end cannot be seperated , they are as a unit. |
The normal Trigger's Sear.
Made of zinc die-cast. |
The normal piston end gets stuck on the sear sideling, When you costum inside od trigger unit, you need delicate adjustment and it is a little difficult for beginners. |
|
|
|
Application Consideration
The normal piston end gets stuck on the sear sideling, When you costum inside od trigger unit,it may break down the balance.
for fix them,needs delicate adjustment and it is a little difficult for beginners.
If you can't make it better, we recommend PDI New Trigger.ifor VSRAfor Bͺj
The detail of "Trigger Problems" is HERE. |
|
|
|
For Normal Trigger Repair Parts.
*You can't use this parts with PDI New Trigger.
We deem to get your agreement for the below policy when you place an order.
|
|
|
1st.VA[@gέθ
|
|
|
1:Insert 2nd.Sear from bottom of 1st.Sear. |
2:Insert the Torsion Spring from top of sears. |
Point!
If you don't know the position of the Torsion Spring, please see this picture. |
|
|
|
3:Please note about the direction of Spring. Spring has shorter wire and longer wire.
Attach longer wire with 2nd.Sear. |
4:Insert pin and fix Sears and Torsion Spring. |
5:Set Sears in the Trigger BOX. |
|
|
|
6:Set the Karu-Bane(bigger one). |
7:Complete. |
|
If you feel trouble, please read "Application consideration" and "Difference between Normal and PDI's Trigger". |
|
|
|
|
For Normal Trigger Repair Parts.
*You can't use this parts with PDI New Trigger.
We deem to get your agreement for the below policy when you place an order.
|
|
|
2nd.VA[@gέθ
|
|
|
1:Insert 2nd.Sear from bottom of 1st.Sear. |
2:Insert the Torsion Spring from top of sears. |
Point!
If you don't know the position of the Torsion Spring, please see this picture. |
|
|
|
3:Please note about the direction of Spring. Spring has shorter wire and longer wire.
Attach longer wire with 2nd.Sear. |
4:Insert pin and fix Sears and Torsion Spring. |
5:Set Sears in the Trigger BOX. |
|
|
|
6:Set the Karu-Bane(bigger one). |
7:Complete. |
|
If you feel trouble, please read "Application consideration" and "Difference between Normal and PDI's Trigger". |
|
|
|
|
For Normal Trigger Repair Parts.
*You can't use this parts with PDI New Trigger.
We deem to get your agreement for the below policy when you place an order.
|
|
|
©ιol^gK[@gέθ
|
|
|
1:Select smaller spring. |
2:Set the Trigger into the BOX. |
3:Set the spring. |
|
©ιol^VA[@gέθ
|
|
|
|
2:After setting 2nd.Sear into 1st.Sear,set them into the Trigger BOX. |
3:After that, set the spring. |
|
|
|
4FComplete. |
|
|
|
|
|
|
For Normal Trigger Repair Parts.
*You can't use this parts with PDI New Trigger.
We deem to get your agreement for the below policy when you place an order.
|
|
|
Zbgs@gέθ
|
|
|
1:You can change Set Pin without opening the trigger BOX.
Insert the Set Pin into the BOX.
|
2:Fix the screw with hexagon wrench. |
3:Complete. |
|
|